Xiaomi Mi PadXiaomi Mi Pad2

Xiaomi Mi Pad2 Teardown

In this guide, I’ll explain how to disassemble Xiaomi Mi Pad2 to remove the back cover, speakers, battery, camera and motherboard. Refer to this guide. You can repair your Xiaomi Mi Pad2.

Want to be the first to see inside the latest gadgets? Follow us on Facebook for the latest news from the MyFixGuide.com.

Specification:
OS: Android 5.1 (MIUI)
Processor: Intel Atom X5-Z8500 quad-core processor, up to 2.2GHz
Graphics Processor: Intel HD Graphics
Memory: 2GB LPDDR3 Dual channel
Storage: 16GB/64GB eMMC4.5
Battery: 6010mAh (min); 6190mAh Lithium-ion Polymer battery
Charging: Supports 5V/2A fast charge
Screen: 7.9-inch IPS screen, resolution of 2048 x 1536, 326 ppi
Camera: 8MP rear camera, f/2.0 aperture, 5MP front camera, f/2.0 aperture

We have prepared this tool screwdriver set, cleaning cloth, suckers and heat gun because heat gun is too big, so we did not take it to the picture.

Remove two screws next to the Micro USB port.

Lift up the back cover a little bit, insert the guitar pick, sliding the pick by the edge, released all the snaps.

Under the back cover, you can access the battery, speakers and motherboard.

Remove four screws securing the speaker. The speakers can be removed.

Product Number: MC151014.E1, it is estimated that the production date of these two elements.

This step should remove the battery because the battery cable is also fixed on the motherboard, so we remove the motherboard cover first. There are ten screws securing the cover.

Under the cover, you can access Mi pad2’s motherboard.
Disconnect the battery connector from the motherboard.

Now heat up the battery for 2 minutes, remove the battery.

Xiaomi Mi Pad2 comes with a 6010mah, 23.08wh Li-polymer battery, Xiaomi part number: BM61.

USB Type C and LCD cable

1. Volume and power button cable
2. Rear camera
3. Front camera
4. Light sensor

Photosensitive sensor and button cable, which is glued the cable to the phone body, so you need to use a heat gun to heat it up, you can remove it easily.

8MP rear camera and 5MP front camera

Only the processor metal shield can be removed, and the other metal shield soldered directly to the motherboard.

Remove the grease. You can find Atom X5-Z8500 processor and two ELPIDA memory chips.

For more guides, check out the Mi Pad2 device page.

15 Comments

  1. Hello. I saw your mi pad 2 dissambly page. Can the RAM be removed and replace with a higher capacity RAM?

    1. unlikely. it is not easily removed and to do so would require very specialised equipment. there is the possibility of larger chips to be installed but there is no guarantee.

  2. Would it be possible to install a very small thumb drive or memory card inside? Maybe wire it with the usb port and maybe even use usb hub?

    1. unless someone finds some pads that carry usb this will not be possible. the space is also very tight so is unlikely to fined space to fit one.

  3. could you please inform me which is the bios chip because i have bricked my device and i have to reprogram bios chip or buy another to replace

  4. Thank you for very useful info. Please show me where test points on the mainboard of Mi Pad 2.

  5. My mi pad 2 has stopped charging, no response when plugged in at all. Will this be battery damage or charging port damage?

    1. Mine still power up if charger is plugged in even if the battery is bad. Not sure though if battery is totally dead (0 volts).

Leave a Reply to David Cancel reply

Your email address will not be published. Required fields are marked *

50  −    =  41