Lenovo PhoneLenovo ZUK Z2

Lenovo ZUK Z2 Teardown

The ZUK Z2 smartphone was launched in April 2016. It has a 5-inch full HD (1920 x 1080) 2.5D curved LTPS display.

ZUK Z2 is powered by a quad-core Qualcomm Snapdragon 820 processor and comes with 4GB of RAM. The phone packs 64GB of internal storage, which cannot be expanded. The 13-megapixel ISOCELL camera is placed on the back of the phone, while you’ll find an 8-megapixel shooter (1.4um pixel size, f/2.0 aperture, 78.9-degree wide-angle lens) at the front.

The phone has a 3,500mAh battery and supports Qualcomm’s Quick Charge 3.0 Tech, which means you’ll be able to charge the battery rather quickly. The Type-C USB port is placed on the bottom of the phone, and so are its speaker and the 3.5mm headphone jack. ZUK Z2 has a metal frame and measures 141.65 x 68.88 x 8.45mm, while it weighs 149 grams.

Teardown is what we do! Follow us on Facebook for the latest repair news.

First of all, remove the SIM card tray. It supports the dual Nano SIM card.

Heat up the edges of the back cover with a heat gun for about 3-5 minutes.
Then, open the back cover with a suction cup.

Remove seven screws securing the top middle frame.

On the back of the top middle frame, we can find the front camera.

Remove the speaker module by removing five screws.

Remove the screws securing the metal plate and disconnect the battery connector from the motherboard.

Pull out two double-sided tapes, and you can remove the battery.

Lenovo ZUK Z2 comes with a 3500mAh Li-polymer battery.

Here’s the Lenovo ZUK Z2 chassis.

All main chips are covered with a metal shield, and there is a layer of graphite sticker on the metal shield.

Here’s the USB Type-C port.

Lenovo ZUK Z2 features a Samsung latest 2M8 13MP camera sensor. It supports PDAF+CAF dual focus mode, which can achieve 0.1 seconds of focus speed.

The bottom board is integrated with a vibrating motor, a microphone and a 3.5mm earphone jack.

Remove two screws securing the side button module.

Here are the Lenovo ZUK Z2 volume keys and lock screen buttons.

U-Touch button

Fingerprint sensor module

Qualcomm Snapdragon 820 + Samsung 4GB RAM
Samsung 64GB ROM
Qualcomm PM8996 Power Management IC
Qualcomm SMB1351 fast charging IC

Qualcomm PM8996 Power Management IC
Qualcomm QCA6164A Wi-Fi IC
Qualcomm WCD9335 Audio decoder chip
Qualcomm WTR3925 RF
QROVO QM58101 PA

Source: it168.com

14 Comments

  1. Hello,

    Thanks for the teardown! To replace the screen, is it necessary to disassemble the Z2 from the back, or can the screen be removed from the front? It would be great if you could provide some instructions for screen replacement, as I couldn’t find any on the web.

    Thanks!

  2. Hi David,

    Well, I took the plunge, bought a replacement screen (in the frame) from AliExpress, and fixed my phone. It seems to work perfectly! I couldn’t have done it without your teardown, so thank you again. The job took me about 2 hours, and I’m pretty much new to this type of work.
    A couple of notes: first, my speaker module had 8 screws, not 5 as you reported. Maybe a different hardware revision? Second, I’d really recommend that anyone who wants to do this should buy the screen in the frame. It’s US$10 more, but it means you don’t have to muck around with removing the broken glass from the frame. The frame came with copper and graphite sheets and adhesive in the right places, so it was really convenient.

    1. RobBrown,

      Could you please share which display you bought? There are many sellers, but I really want to have the adhesive, etc., included.

      Thanks!

  3. RobBrownNZ,

    Thanks, found it! I also scratched the frame on all corners, so this one is perfect!
    The glass is broken, but the digitizer is still functional. I ordered one and I will follow the teardown as soon as I receive the display.

  4. M,
    Good to hear. I didn’t have any real problems. The scariest part was removing the ribbon cable from the fingerprint sensor. I protected the sensor itself with tin foil and heated the frame from the front, and it ended up coming off pretty easily.
    Let us know how you get on!
    Skynix 8GB PC3L-12800S RAM

  5. Hi!
    Is the front glass equal to the digitizer?
    Is it possible to replace only the front glass? Without changing the LCD?
    Or is it glued to the LCD?

    Thanks

  6. I’d like to ask once again about replacing only the touch panel. Is it possible without loca glue and a special UV lamp?
    Thanks in advance.
    BEST REGARDS
    Martin

  7. Hi, so I dropped my phone and it landed on the front. Now, there is no touch response in the middle of the screen. I think the digitizer is broken. I have already ordered a new front panel with an LCD digitizer to replace this one.

    Also, the GPS stopped working shortly after. Now, I don’t get a lock on my GPS anymore. Should I replace the GPS/Wi-Fi board to fix this issue, or is this a software issue?

Leave a Reply

Your email address will not be published. Required fields are marked *

  −  6  =  3